We ship these instruments and testkits advantageously world-wide. We discount Hanna's Australian list prices. Freight charges to other destinations are minimal.
We hold some these items in stock; Hanna Australia has most of them available for immediate shipment.
The instruments will be shipped within a week.
This page shows a selection of popular Hanna meters. A complete list of instruments is linked to the Hanna USA catalogue. All information on the USA site is current, however, the literature downloads contain information specific to the USA market only.
Please choose your requirements and then ask ProSciTech for a quotation. Please don't double up by asking Hanna Australia too, comparing with the same model makes no sense. Particularly since we supply meters freight free (within Oz) and give a small discount on expensive meters.
Instruments: 1 year
Electrodes: 6 months
ATC - Automatic Temperature Compensation
COD - Chemical Oxygen Demand
DO - Dissolved Oxygen
EC - Electrical Conductivity
ISE - Ion-Specific Electrode
mV - milli-Volt
ORP - Oxidation Reduction Potential
TDS - Total Dissolved Solids
FTU/NTU - Formazin/ Nephelometric Turbidity Units
pH/ ORP/ ISE METERS
The pHep 4, accuracy ±0.1pH, and pHep 5, accuracy ±0.05pH, include features such as a dual-level LCD, battery level indicator, replaceable pH electrode cartridge, stability indicator, automatic shut-off and automatic calibration all in a floating, waterproof casing.
The testers are supplied with protective cap, electrode removal tool, batteries and instructions.
These combination waterproof testers offer high accuracy pH, EC/ TDS and temperature measurements in a single instrument. No more switching between meters for your routine measurements. The waterproof testers (they even float) have a large, easy-to-read, dual-level LCD and automatic shut-off. pH and EC/ TDS readings are automatically compensated for the effects of temperature (ATC).
These technologically advanced testers have a replaceable pH electrode cartridge with an extendable cloth junction, as well as an EC/ TDS graphite electrode that resists contamination by salts and other substances, giving these meters a greatly extended life.
The EC/TDS conversion factor is user selectable as is the temperature compensation coefficient (ß).
The testers are supplied with protective cap, electrode removal tool, batteries and instructions.
EHIE1285-6 is a multi-pin pH electrode for HI 9813-6, with cloth junction, 7-pole, 2m cable, for greenhouses, hydroponics, environmental monitoring, water treatment, boilers and cooling towers. HI 9813-6 is a waterproof pH/EC/TDS/°C meter with pH electrode diagnostics.
Specifications and manual for EHI98129
Specifications and manual for EHI98130
Specifications for EHIE1285-6
EHI 314 is a rugged portable pH meter designed to be easy-to-use, yet reliable and practical. It is ideal for education and measurements in the field.
Simple pH calibration is performed manually through 2 trimmers. Measurements are automatically compensated for variations in temperature.
EHI8314 shows the reading together with the current mode (pH, mV or °C). A low battery indicator will alert the user when the battery needs to be replaced.
EHI8314 is supplied with HI 1217D pH electrode, calibration and cleaning solutions, calibration screwdriver, battery, protective case and instructions.
Two models are available:
EHI8314 uses pH electrodes with DIN connector and internal temperature sensor.
EHI83141 is provided with separate connectors for pH electrode (BNC) and temperature probe.
Specifications and manual for EHI8314
Measures pH, Conductivity, and Dissolved Oxygen
Edge’s groundbreaking design is the culmination of Hanna’s vision, design capabilities, integrated production and world class R&D. Edge® is a single meter that can measure pH, Conductivity, Dissolved Oxygen and is incredibly easy to use. We put a lot of thought into edge’s ease of use.
The EHI2221 is a pH benchtop metre featuring Calibration Check™ diagnostics for pH electrodes and buffer solutions during calibration. This instrument compares the characteristics of the pH electrode from one calibration to the next. In the case of large variances in the electrode condition, it alerts the user that the electrode needs to be properly cleaned prior to calibration and measuring. The second feature is to detect if the calibration buffer solution is contaminated. After calibration, the probe condition is evaluated and an indicator is displayed, informing the user of the overall pH electrode status. This instrument can measure ORP using ORP electrodes (pH channel input), due to its capability to measure mV with a resolution up to 0.1 mV. It also features five point calibration with seven standard buffers, automatic temperature compensation and GLP capabilities that allow for the storage and retrieval of all data regarding pH. With a built-in logging function, measurements are stored in non volatile memory and can be transferred to a PC through the USB port.
- pH Calibration Check™
- On-screen electrode condition and response time
- Up to five point calibration with seven standard buffers
- Diagnostic alerts through icons
- Automatic temperature compensation
- GLP features
- PC interface via USB
EHI2211 is a benchtop pH/ORP and °C meter. EHI2211 adds measurement for ion concentration (ISE) and Oxidation Reduction Potential (ORP) in the mV range.
This instrument also features a reading stability indicator used during calibration and a measurement memory/memory recall function.
pH measurements for both instruments are compensated for the temperature effect manually or automatically with the EHI7662 temperature probe. This metre is equipped with an easy-to-read LCD which shows both the primary reading and °C.
- Simple to operate
- Automatic Temperature Compensation
- Automatic calibration
- Calibration expiration reminder
- ORP range
|Range||pH||-2.00 to 16.00 pH|
|mV||±399.9 mV; ±2000 mV|
|Temperature||-20 to 120.0°C|
|mV||0.1 mV; 1 mV|
|mV||±0.2 mV (±399.9 mV); ±1 mV (±2000 mV)|
|Temperature||±0.4 °C (excluding probe error)|
|pH Calibration||automatic, 1 or 2 point with 5 memorised buffer values (pH 4.01, 6.86, 7.01, 9.18, 10.01)|
|Temperature Compensation||automatic (with HI 7662 probe) or manual from -9.9 to 120 °C|
|pH Electrode||HI 1131B, glass-body, single junction, refillable, BNC connector, 1 m cable (included)|
|Temperature Probe||HI 7662 with 1 m (3.3') cable (included)|
|Input Impedance||1012 Ohm|
|Power Supply||12 VDC adapter (included)|
|Environment||0 to 50°C (32 to 122°F); RH max 95%|
|Dimensions||235 x 222 x 109 mm (9.2 x 8.7 x 4.3?)|
|Weight||1.3 kg (2.9 lbs.)|
The Primo TDS tester provides a fast and dependable way to measure the Total Dissolved Solids in water samples. It is ideally suited for the rigorous demands of water quality professionals, who will appreciate the practicality of Primo's easy-to-read LCD when demonstrating the before and after results of conditioning and filtration systems. Temperature is compensated automatically to ensure the readings are consistent to the standard or reference temperature.
Operating and routine maintenance has never been easier. Primo TDS uses a single button at the top of the meter. Press it once and the meter is powered and ready for use. Press and hold the button for a few seconds and Primo automatically enters calibration mode. Simply open a sachet of the calibration solution, dip the probe and within seconds the meter recognises the calibration solution and calibrates itself. Maximum battery life is managed by Primo's power microprocessor, which automatically turns it of after 5 minutes of inactivity.
The Primo 1, 3 and 4 testers have been designed for those hard-to-reach places where standard testers are not particularly suitable. The specially designed conductivity/TDS probe, supplied with the Primo series, is attached to a 1 meter cable. This helps insertion in inaccessible or low level places without the operator having to maneuver into awkward positions merely to take a reading.
The testers are supplied with batteries and instructions.
Specifications and manual for Primo 2
Specifications and manual for Primo 3
Primo: EC/TDS tester, range 1 - 1999ppm
Primo 1: EC/TDS tester, range 1 - 1999ppm, with 1m cable
Primo 2: EC/TDS/°C tester, range 1 - 1999ppm, 1 - 60°C
Primo 3: EC/TDS/°C tester, range 1 - 1999ppm, 1 - 60°C, with 1m cable
Primo 4: EC/TDS tester, range 1 - 10mS/cm, with 1m cable
Primo 5: EC/TDS tester, range 1 - 1999µS/cm
EHI8633 and EHI8733 have been designed specifically for use in areas of production and quality control. It is often necessary to test samples with different concentrations ranging from deionised water to brine.
The amperometric system would require constant recalibration and probe changes, thus making the measurement process very time consuming and unreliable. To solve this problem, HANNA® has developed the EHI8633, which uses a 4-ring potentiometric probe. The rugged probe is made of PVC - ideal for indoor, as well as outdoor measurements.
By using one point calibration, it is now possible to obtain accurate readings across a very wide range, from 0.1 to 199900 µS/cm.
If temperature of the solution fluctuates, EHI8733, with a built-in temperature sensor and Automatic Temperature Compensation, is the perfect instrument.
EHI8733 is supplied with HI 76302W probe with internal temperature sensor & 1m cable, calibration screwdriver, calibration solutions, protective case, battery and instructions.
As an accessory, HI 710133 is available. This kit includes a rugged carrying case with a beaker, a calibration screwdriver and standardising solution at 12880 µS/cm.
Specifications and manual for EHI8733
EHI8633 comes without the temperature sensor.
The EEC215 is a multi-range bench top conductivity meter with four measurement ranges to ensure the highest resolution and accuracy to meet your measuring requirements.
Calibration is performed manually up to 1-point simply by adjusting a knob on the front of the meter. With a user selectable temperature coefficient and a temperature sensor incorporated in the probe, temperature compensation of the reading is automatic.
Included with this meter is the fast responding HI 76303 probe. This probe is equipped with a 4-ring platinum sensor, built-in internal temperature sensor and a 1m cable, which can be used for measuring highly acidic or alkaline samples, or at high temperatures.
EEC215 is supplied with 12 Vdc adapter and instructions.
Specifications and manual for EEC215
EHI8734 has been specifically designed for the water conditioning industry, particularly in the softening, demineralisation, reverse osmosis and drinking water applications.
Three ranges of measurement assure the highest accuracy possible. All three ranges can be executed at the touch of a button without having to change the conductivity probe. This makes it very easy to switch applications without having to worry about recalibration.
To add to the meter's accuracy and efficiency, Manual Temperature Compensation is possible through a knob on the front panel.
The 4-ring potentiometric probe, HI 76301D, is made of rugged PVC for the best protection in the field and is supplied with a 1m cable to access hard to reach areas.
The ratio between conductivity and TDS is factory calibrated at 0.5 (CaCO3 value).
EHI8734 is comes with with calibration screwdriver, calibration solutions, protective case, battery and instructions.
Specifications and manual for EHI8734
HI 98280 GPS Multiparameter metre with Fast Tracker™ tag identification system
HI 93414 EPA compliant portable turbidity and chlorine metre with Fast Tracker™
HI 9813-6 Waterproof pH/EC/TDS/temperature metre with pH electrode diagnostic
HI 9813-5 Waterproof pH/EC/TDS/temperature metre for growers
HI 9813-0 Waterproof pH/EC/TDS metre for growers
HI 9812-5 Versatile instruments for water conditioning
HI 9811-5 pH, conductivity to 6000 µS/cm and temperature meter, water resistant
HI 98204 pH/ORP/EC/temperature in one unit
- Substitutes two or three meters
- Better accuracy, great repeatability & long battery life
- Ergonomic design
pH/ORP/ISE, EC/TDS/Resistivity/Salinity/Seawater Specific Gravity, Turbidity, DO, Temperature and Atmospheric Pressure
- Field replaceable ISO 7027 compliant turbidity sensor
- Ammonium, chloride and nitrate ISE's
- Logging from probe or meter
- Fully customizable instrument, probe, sensors and measurement specifications
- Display from 1 to 12 parameters with font dimension adjustment
- Field replaceable sensors
- pH/ORP or pH, four electrode EC and galvanic DO sensors
- Auto-recognition of all sensors
- Rugged probe with stainless steel tip has a diameter under 2" for wells and pipes
- Fast Tracker™-Tag I.D. System simplifies periodic monitoring
- Features a built-in barometer for DO compensation
- Quick or independent sensor calibration feature
- Measurement check eliminates erroneous readings
- Logged data can be displayed as graphs
- Graphic LCD with backlight
- USB for PC connectivity
- Good Laboratory Practice feature with last five calibrations recorded
- Meter accepts both alkaline and rechargeable batteries
- Waterproof protection for metre (IP67) and probes (IP 68)
Supplied as a kit. This metre will also take a turbidity sensor (cheaper to order a turbidity capable kit then add it later if turbidity is required) as well as ISE sensors which can be added later.
Software is supplied.
Spare multi-pin pH/EC electrode with temperature sensor, cloth junction, gel-filled, 7-pole; 2 m cable, for greenhouses, hydroponics, environmental monitoring, water treatment, boilers and cooling towers.
Suitable for the following Hanna meters:
HI 9811-5 - pH, conductivity to 6000 µS/cm and temperature with a water-resistant meter
HI 9812-5 - versatile instruments for water conditioning
HI 9813-5 - waterproof pH/EC/TDS/temperature meter for growers
Specifications and dimensions
for the Laboratory and Beer Testing
Refillable, combination pH electrode for general laboratory purposes as well as beer testing
|Junction/flow rate||Ceramic, single / 15-20 µL/h|
|Electrolyte||KCl 3.5M + AgCl|
|Max pressure||0.1 bar|
|Range||pH: 0 to 13|
|Recommended operating temperature||20 to 40°C|
|Tip/shape||Spheric (dia: 9.5 mm)|