rapid-core sampling tool biopsy punch
PROSCITECH RAPID‐CORE® BIOPSY PUNCHES

sampling tool, retractable, with plunger

10% discount when you purchase more than 5 units.
20% discount when you purchase a carton of 25 units.


Features

  • Punches through most thin, soft substrates including but not limited to; skin, tissue, gels, paper, cloth, leaves, paint chips, films.
  • Pen style, mechanism extends the cutting tip from inside the case, locking it into position, and protects the user from accidentally touching the sharp edge when not in use.
  • A push button is used to eject the sample out of the cutting tip.
  • Each tool comes sterile, marked and individually packaged and sealed.
  • Orders of 25 units are shipped in a branded cardboard storage box.

Material

The body of the tool is made from Polypropylene (PP) and the cutting tip from stainless steel 304 (SS304).


Ordering Information

CodeSize (mm)ID (mm)OD (mm)Wall Thickness (mm)
T983‐030.350.330.630.15
T983‐050.50.500.800.15
T983‐070.750.771.070.15
T983‐101.00.961.260.15
T983‐121.21.21.50.15
T983‐151.51.51.90.20
T983‐202.02.02.40.20
T983‐252.52.52.90.20
T983‐303.03.03.40.20
T983‐353.53.53.90.20
T983‐404.04.04.40.20
T983‐505.05.05.50.25
T983‐606.06.06.50.25
T983‐707.07.07.50.25
T983‐808.08.08.50.25


Shelf Life

The tool will not perish if left sealed for long periods of time, however it is recommended that you re‐sterilise the tool after 2 years.


Sterilisation

Each tool is packed into a sterilisation pouch and heat treated for 20 minutes at 121°C (250°F) / 15 psi with Ethylene Oxide (EO). The special paper package allows for the EO gas to pass through the pores of the paper.

Tools can be re‐sterilised by rinsing the tip in ethanol and autoclave at the above settings.


Cleaning

If you choose to use these punches repeatedly, the recommended cleaning procedure is as follows;

  • Clean tip between each sample extraction by coring blank filter paper over a cutting mat
  • Rinse tip with ethanol and/or spray with compressed air to remove dried artifacts
  • Rinse mat with ethanol after each sample extraction.
T983-03
Rapid-Core® Biopsy punches, retractable, with plunger, 0.35mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-05
PROSCITECH Rapid-Core® Biopsy punches, retractable, with plunger, 0.5mm
10% DISCOUNT FOR 5
AUD11.00
ea
ADD TO CART 
T983-07
Rapid-Core® Biopsy punches, retractable, with plunger, 0.75mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-10
PROSCITECH Rapid-Core® Biopsy punches, retractable, with plunger, 1.0mm
10% DISCOUNT FOR 5
AUD11.00
ea
ADD TO CART 
T983-12
Rapid-Core® Biopsy punches, retractable, with plunger, 1.2mm
10% DISCOUNT FOR 5
AUD11.00
ea
ADD TO CART 
T983-15
Rapid-Core® Biopsy punches, retractable, with plunger, 1.5mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-20
Rapid-Core® Biopsy punches, retractable, with plunger, 2.0mm
10% DISCOUNT FOR 5
AUD11.00
ea
BACKORDER 
T983-25
Rapid-Core® Biopsy punches, retractable, with plunger, 2.5mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-30
Rapid-Core® Biopsy punches, retractable, with plunger, 3.0mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-35
Rapid-Core® Biopsy punches, retractable, with plunger, 3.5mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-40
Rapid-Core® Biopsy punches, retractable, with plunger, 4.0mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-50
Rapid-Core® Biopsy punches, retractable, with plunger, 5.0mm
10% DISCOUNT FOR 5
AUD11.00
ea
ADD TO CART 
T983-60
Rapid-Core® Biopsy punches, retractable, with plunger, 6.0mm
10% DISCOUNT FOR 5
AUD15.00
ea
BACKORDER 
T983-70
Rapid-Core® Biopsy punches, retractable, with plunger, 7.0mm
10% DISCOUNT FOR 5
AUD15.00
ea
ADD TO CART 
T983-80
PROSCITECH Rapid-Core® Biopsy punches, retractable, with plunger, 8.0mm
10% DISCOUNT FOR 5
AUD11.00
ea
ADD TO CART 
Biopsy punches with plungers
Biopsy punches with plungers
BIOPSY PUNCHES, WITH PLUNGER

Please note: due to manufacturing issues, this range is only available while stocks last. They will be replaced by our own ProSciTech Pty Ltd brand of sampling tools available above (T983‐**). There may also be limited stock of Miltex and Harris branded tools below (T980‐** and T984‐**).


Sterile punches with razor sharp cutting tip and a plunger to expel the sample. Tip diameter is indicated on the handle. Individually packed in a pouch and EO sterilised.

Features

  • Seamless construction ensures a zero drag operation
  • Double grinding produces a razor sharp punch that lasts much longer than ordinary punches
  • Controlled size for a precise specimen size
  • Rigid ribbed design gives a good grip
  • Cap to protect the tip
  • Manufactured in accordance with ISO 13485:2003

Note: The sell unit is 5 punches. 15% discount for 25 punches, 20% for 100 punches.


Please note: due to manufacturing issues, this range is only available while stocks last. They will be replaced by our own ProSciTech Pty Ltd brand of sampling tools available above (T983‐**). There may also be limited stock of Miltex and Harris branded tools below (T980‐** and T984‐**).

T982-10
Biopsy punches, with plunger, 1.0mm
15% DISCOUNT FOR 5
AUD32.00
pk/5
ADD TO CART 
T982-12
Biopsy punches, with plunger, 1.25mm
15% DISCOUNT FOR 5
AUD32.00
pk/5
ADD TO CART 
T982-25
Biopsy punches, with plunger, 2.5mm
15% DISCOUNT FOR 5
AUD32.00
pk/5
ADD TO CART 
T982-30
Biopsy punches, with plunger, 3.0mm
15% DISCOUNT FOR 5
AUD32.00
pk/5
ADD TO CART 
T982-35
Biopsy punches, with plunger, 3.5mm
15% DISCOUNT FOR 5
AUD32.00
pk/5
ADD TO CART 
T984 Miltex® biopsy punch with plunger
T984 Miltex® biopsy punch with plunger
Cutting mat
Cutting mat
DISCONTINUED BIOPSY PUNCHES

Miltex and Harris Uni-Core

These biopsy punch with plunger are a disposable coring tool designed to core, punch and retrieve samples from thin or soft substrate source materials such as tissue, gels, paper, cloth, leaves, paint chips and films. Ribbed plastic embossed handle with a razor sharp seamless stainless steel cutting tip. Each punch is individually packaged sterile, with a shelf life of 5 years. The punches have an internal plunger designed for safe and efficient removal of the specimen from the tip.


They are available while stocks last, in 6 core size diameters: 1.0, 1.5, 2.0, 3.0, 4.0 and 6.0mm. All punches are colour coded by size.
This is a disposable sampling tool, ideal for tissue processing or forensic applications. For some applications where contamination is not an issue, the punch is reusable after cleaning.


Cleaning: clean tip between each sample extraction by coring blank filter paper; rinse with ethanol or spray with compressed air to remove dried artifacts. Rinse mat with ethanol after each sample extraction. Autoclave 20 minutes at 120°C and 15 p.s.i.
Alternatively, see Struycken punch‐cutting forceps on page T8.


Miltex: Made in Japan

Harris: Made in Taiwan

T980-60
Harris Uni-Core, 6.0mm
60% DISCOUNT FOR 1
AUD5120.40
ea
ADD TO CART 
T984-10
Miltex® biopsy punch with plunger, 1.0mm
15% DISCOUNT FOR 5
AUD19.00
ea
BACKORDER 
T984-15
Miltex® biopsy punch with plunger, 1.5mm
15% DISCOUNT FOR 5
AUD19.00
ea
BACKORDER 
T984-20
Miltex® biopsy punch with plunger, 2.0mm
15% DISCOUNT FOR 5
AUD19.00
ea
BACKORDER 
T984-30
Miltex® biopsy punch with plunger, 3.0mm
15% DISCOUNT FOR 5
AUD19.00
ea
BACKORDER 
T984-40
Miltex® biopsy punch with plunger, 4.0mm
15% DISCOUNT FOR 5
AUD19.00
ea
BACKORDER 
T984-M
Cutting mat, self-healing, 140 x 89mm
AUD17.00
ea
BACKORDER 
Silicone sterilisation matt for operating instrumentst
Silicone sterilisation matt for operating instrumentst
Silicone mat
Silicone mat
SILICONE STERILISATION MAT

Silicone pin mats hold operating instruments in position, supported by soft spines. Lifting instruments off this mat is safer and easier since tools are supported by small protrusions, contaminants are not transferred to other tools, but drain through holes in the mat. These mats are easily cleaned and tolerate numerous cycles in an autoclave.


The silicone sterilisation tray mats are manufactured in line with RoHS and FDA standards, and can be used to cushion, protect and organise surgical instruments for sterilisation. Perforations allow for proper exposure and ventilation during the sterilisation process. The silicone pin mats can also be cut into smaller sections to fit any size basket or box.


Silicone is well known for its use in food, pharmaceutical and other clean industry applications and offers many advantages over other elastomers. It is non-toxic, easy to clean and does not retain odours. It is a resilient material, capable of maintaining many of its properties at extremely low and high temperatures (-40°C to 250°C). It is naturally electrically insulating. Silicone is highly tear-resistant and is unaffected by many solvents, including petrol.

TM76
Pin mat for sterilisation trays, silicone, 760 x 480 x 19mm
AUD124.00
ea
ADD TO CART 
Universal Tray
UNIVERSAL TRAYS

Laboratory Tray / Utility Tray

Adding to the already existing range of autoclavable laboratories trays, this tray can be utilised for purposes ranging from drying glassware to sterilising and to store any laboratory apparatus.


Small: 203 x 152 x 51mm

Large: 254 x 203 x 51mm

T990L
Instrument tray, SS, 254 x 203 x 51mm
AUD33.00
ea
ADD TO CART 
T990S
Instrument tray, SS, 203 x 152 x 51mm
AUD25.00
ea
ADD TO CART 
Instrument Box for sterilising
Instrument Box for sterilising
INSTRUMENT TRAY

Instrument Box

This multipurpose tray that can be used for sterilising, drying glassware, porecelainware & other laboratory instruments - steam autoclavable.

The handles assist in carrying reagents or laboratory apparatus from one place to another, single handedly.

T991-200
Instrument box, SS, 200 x 100 x 50mm
10% DISCOUNT FOR 5
AUD27.00
ea
BACKORDER 
T950 Micro-needle probe set
T950 Micro-needle probe set
T952 Straight probe
T952 Straight probe
MICRO-NEEDLE PROBE SET

The set includes one lightweight, precision handle and four interchangeable hardened steel tools for manipulating, scribing, spring assembly and probing. The precision handle is finely balanced, non-rolling, gold anodized with a split collet mounting and knurled lock nut. Length is 120mm
The precision forged tools are made of hardened nickel-plated tool steel, 40mm long with a 2mm diameter shank reduced to a 0.7mm (0.027") diameter. All tools are tapered to a sharp tip. Plastic container.

T950
Micro-needle probe set
AUD47.00
set
ADD TO CART 
T952
Straight prober
AUD14.00
ea
BACKORDER 
T9 plus above numbers are our catalogue numbers. Click to enlarge image.
T9 plus above numbers are our catalogue numbers. Click to enlarge image.
T901-0120, needle diameter is 0.12mm
T901-0120, needle diameter is 0.12mm
T900 - Micro-tool handle & T901 Micro-needle, long, steel shank, and short, reduced shank 0.12mm diameter
T900 - Micro-tool handle & T901 Micro-needle, long, steel shank, and short, reduced shank 0.12mm diameter
MICRO-TOOL

with interchangeable micro-tips, ideal for finest dissections

Micro‐Tools are the smallest available precision instruments for laboratory and production use. Micro‐Tools are available in different tip configurations with interchangeable tool handle. A threaded (tapped) handle (T900), this holds the tool. The tool is threaded for fixing to the handle, and holds in the case of T901 a needle 15mm x 0.5mm. The last 2mm of the needle are stepped down to only 0.12mm thick, and have a microscopic needle point ‐ see above image. Tools on 0.5mm or larger shanks are not stepped down. Tip material is hardened tool steel unless otherwise noted.


For micro‐tool storage box see T900‐BOX below.


Caution: Micro‐tools are very fine, hard and brittle. Take special care when removing from the tube. Press the blue square holding the tool onto a flat surface with the tube up at a shallow angle. Hold the tube near the other end and gently twist back and forth while pulling very lightly. The tube will suddenly clear the blue plastic, and the tool could easily touch the tube. Some tools are on a barely visible shaft extending slightly from the larger shaft. Practice removal first using the opposing blue stopper which does not hold a tool. See image below for clarification.


Note: Tools are packed by the manufacturer in perfect conditions. These tools like diamond knives and sapphire micro‐scalpels are assumed to have been shipped in perfect conditions and any problems almost certainly are due to mishandling.

IMPORTANT: How to safely remove a micro-tool - CLICK TO ENLARGE
IMPORTANT: How to safely remove a micro-tool - CLICK TO ENLARGE
T900
Micro-tool handle
AUD43.00
ea
ADD TO CART 
T901-0025
Micro-needle, long, shank size 0.025mm
AUD134.00
ea
BACKORDER 
T901-0120
Micro-needle, long, shank size 0.12mm
AUD113.00
ea
BACKORDER 
T901-0250
Micro-needle, long, shank size 0.25mm
AUD84.00
ea
ADD TO CART 
T901-0500
Micro-needle, long, shank size 0.5mm
AUD63.00
ea
ADD TO CART 
T901-1000
Micro-needle, long, shank size 1.0mm
AUD75.00
ea
ADD TO CART 
T902-0120
Micro-engraver, triangular, shank size 0.12mm
AUD143.00
ea
ADD TO CART 
T902-0250
Micro-engraver, triangular, shank size 0.25mm
AUD121.00
ea
BACKORDER 
T902-0500
Micro-engraver, triangular, shank size 0.5mm
AUD111.00
ea
BACKORDER 
T902-1000
Micro-engraver, triangular, shank size 1.0mm
AUD116.00
ea
BACKORDER 
T903-0025
Micro-chisel, shank size 0.025mm
AUD148.00
ea
BACKORDER 
T903-0120
Micro-chisel, shank size 0.12mm
AUD119.00
ea
BACKORDER 
T903-0250
Micro-chisel, shank size 0.25mm
AUD91.00
ea
BACKORDER 
T903-0500
Micro-chisel, shank size 0.5mm
AUD84.00
ea
BACKORDER 
T903-1000
Micro-chisel, shank size 1.0mm
AUD91.00
ea
ADD TO CART 
T904-0025
Micro-spade, shank size 0.025mm
AUD148.00
ea
BACKORDER 
T904-0120
Micro-spade, shank size 0.12mm
AUD119.00
ea
BACKORDER 
T904-0250
Micro-spade, shank size 0.25mm
AUD91.00
ea
BACKORDER 
T904-0500
Micro-spade, shank size 0.5mm
AUD84.00
ea
BACKORDER 
T904-1000
Micro-spade, shank size 1.0mm
AUD91.00
ea
BACKORDER 
T905-0250
Micro-fork, shank size 0.25mm
AUD100.00
ea
BACKORDER 
T905-0500
Micro-fork, shank size 0.5mm
AUD76.00
ea
BACKORDER 
T906-0500
Micro-mirror, forward 20°, Ø 5mm, shank size 0.5mm
AUD100.00
ea
BACKORDER 
T907-0500
Micro-ruler, 10mm, 0.1mm divisions, shank size 0.5mm
AUD110.00
ea
BACKORDER 
T908-0025
Micro-knife, 20°, shank size 0.025mm
AUD149.00
ea
BACKORDER 
T908-0120
Micro-knife, 20°, shank size 0.12mm
AUD120.00
ea
BACKORDER 
T908-0250
Micro-knife, 20°, shank size 0.25mm
AUD92.00
ea
ADD TO CART 
T908-0500
Micro-knife, 20°, shank size 0.5mm
AUD84.00
ea
ADD TO CART 
T908-1000
Micro-knife, 20°, shank size 1.0mm
AUD92.00
ea
BACKORDER 
T909-0025
Micro-knife, 45°, shank size 0.025mm
AUD140.00
ea
BACKORDER 
T909-0120
Micro-knife, 45°, shank size 0.12mm
AUD120.00
ea
BACKORDER 
T909-0250
Micro-knife, 45°, shank size 0.25mm
AUD92.00
ea
ADD TO CART 
T909-0500
Micro-knife, 45°, shank size 0.5mm
AUD84.00
ea
ADD TO CART 
T909-1000
Micro-knife, 45°, shank size 1.0mm
AUD92.00
ea
BACKORDER 
T910-0500
Micro-mirror, reverse, shank size 0.5mm
AUD95.00
ea
BACKORDER 
T911-0250
Micro-prober, 90°, shank size 0.25mm
AUD92.00
ea
BACKORDER 
T911-0500
Micro-prober, 90°, shank size 0.5mm
AUD76.00
ea
BACKORDER 
T912-0250
Micro-prober, 45°, shank size 0.25mm
AUD89.00
ea
BACKORDER 
T912-0500
Micro-prober, 45°, shank size 0.5mm
AUD84.00
ea
BACKORDER 
T913-0025
Micro-engraver, oval, shank size 0.025mm
AUD141.00
ea
BACKORDER 
T913-0120
Micro-engraver, oval, shank size 0.12mm
AUD121.00
ea
BACKORDER 
T913-0250
Micro-engraver, oval, shank size 0.25mm
AUD93.00
ea
BACKORDER 
T913-0500
Micro-engraver, oval, shank size 0.5mm
AUD85.00
ea
BACKORDER 
T913-1000
Micro-engraver, oval, shank size 1.0mm
AUD93.00
ea
BACKORDER 
T914-0500
Micro-brush, single natural fibre, shank size 0.5mm
AUD84.00
ea
BACKORDER 
T915-0250
Micro-diamond scribe, 60°, shank size 0.25mm
AUD134.00
ea
BACKORDER 
T915-0500
Micro-diamond scribe, 60°, shank size 0.5mm
AUD88.00
ea
ADD TO CART 
T916-0500
Micro-spatula, flexible, shank size 0.5mm
AUD98.00
ea
BACKORDER 
T917-0500
Micro-manipulator, A-type, shank size 0.5mm
AUD92.00
ea
BACKORDER 
T918-0250
Micro-hook, 90°, shank size 0.25mm
AUD96.00
ea
BACKORDER 
T918-0500
Micro-hook, 90°, shank size 0.5mm
AUD86.00
ea
BACKORDER 
T919-0500
Micro-burnisher, glass sphere, shank size 0.5mm
AUD75.00
ea
BACKORDER 
T920-0250
Micro-hook, 180°, shank size 0.25mm
AUD93.00
ea
BACKORDER 
T920-0500
Micro-hook, 180°, shank size 0.5mm
AUD86.00
ea
BACKORDER 
T921-0025
Micro-scraper, triangular, shank size 0.025mm
AUD141.00
ea
BACKORDER 
T921-0120
Micro-scraper, triangular, shank size 0.12mm
AUD121.00
ea
BACKORDER 
T921-0250
Micro-scraper, triangular, shank size 0.25mm
AUD93.00
ea
BACKORDER 
T921-0500
Micro-scraper, triangular, shank size 0.5mm
AUD85.00
ea
BACKORDER 
T921-1000
Micro-scraper, triangular, shank size 1.0mm
AUD93.00
ea
BACKORDER 
T922-0500
Micro-saw, shank size 0.5mm
AUD85.00
ea
BACKORDER 
T923-0500
Micro-scale, 5mm, 0.1mm divisions, shank size 0.5mm
AUD130.00
0.5mm
BACKORDER 
T924-0025
Micro-needle, short, shank size 0.025mm
AUD98.00
ea
BACKORDER 
T924-0120
Micro-needle, short, shank size 0.12mm
AUD95.00
ea
ADD TO CART 
T924-0250
Micro-needle, short, shank size 0.25mm
AUD75.00
ea
BACKORDER 
T924-0500
Micro-needle, short, shank size 0.5mm
AUD55.00
ea
BACKORDER 
T924-1000
Micro-needle, short, shank size 1.0mm
AUD75.00
ea
BACKORDER 
T925-0120
Ultra micro-needle, tungsten, straight, tip radius 5µm, shank size 0.12mm
AUD120.00
ea
BACKORDER 
T925-0250
Ultra micro-needle, tungsten, straight, tip radius 5µm, shank size 0.25mm
AUD100.00
ea
BACKORDER 
T925-0500
Ultra micro-needle, tungsten, straight, tip radius 5µm, shank size 0.5mm
AUD89.00
ea
BACKORDER 
T926-0120
Ultra micro-needle, tungsten, 30°, tip radius 5µm, shank size 0.12mm
AUD125.00
ea
BACKORDER 
T926-0250
Ultra micro-needle, tungsten, 30°, tip radius 5µm, shank size 0.25mm
AUD102.00
ea
BACKORDER 
T926-0500
Ultra micro-needle, tungsten, 30°, tip radius 5µm, shank size 0.5mm
AUD84.00
ea
ADD TO CART 
T927-0120
Ultra micro-needle, tungsten, 90°, tip radius 5µm, shank size 0.12mm
AUD124.00
ea
BACKORDER 
T927-0250
Ultra micro-needle, tungsten, 90°, tip radius 5µm, shank size 0.25mm
AUD107.00
ea
BACKORDER 
T927-0500
Ultra micro-needle, tungsten, 90°, tip radius 5µm, shank size 0.5mm
AUD97.00
ea
BACKORDER 
T928-0025
Micro-scribe, tungsten carbide, tip radius 5µm, shank size 0.025mm
AUD154.00
ea
BACKORDER 
T928-0120
Micro-scribe, tungsten carbide, tip radius 5µm, shank size 0.12mm
AUD126.00
ea
BACKORDER 
T928-0250
Micro-scribe, tungsten carbide, tip radius 5µm, shank size 0.25mm
AUD96.00
ea
BACKORDER 
T928-0500
Micro-scribe, tungsten carbide, tip radius 5µm, shank size 0.5mm
AUD85.00
ea
BACKORDER 
T929-0250
Micro-diamond file, round, shank size 0.25mm
AUD121.00
ea
BACKORDER 
T929-0500
Micro-diamond file, round, shank size 0.5mm
AUD99.00
ea
BACKORDER 
T930-0500
Micro-diamond file, triangular, 1mm edge to edge, shank size 0.5mm
AUD119.00
ea
BACKORDER 
T931-0500
Micro-loop, Ø 2mm, shank size 0.5mm
AUD69.00
ea
BACKORDER 
T932-0500
Micro-hook, anti-snag guard, shank size 0.5mm
AUD92.00
ea
BACKORDER 
Storage box for 8 micro-tool tips
Storage box for 8 micro-tool tips
MICRO-TOOL STORAGE BOX

Hardwood storage box for 8 micro-tool tips and 1 handle.

Note: Tools not included.

T900-BOX
Micro-tool storage box for 8 tips and handle
AUD117.00
ea
BACKORDER 
T960-60S Diamond scribe
T960-60S Diamond scribe
DIAMOND SCRIBES, 60° TIP

60° Diamond tip for very fine markings.
The finish on these scribing tools creates an optimum cutting edge for high accuracy and long life.
Tip is very fine, mounted on a the end of the metal shaft - which extrudes from the tip of the pen - (shaft ~0.7mm in diameter).

T960-60S
Diamond scribe, 100mm handle, 60° tip, straight
10% DISCOUNT FOR 10
AUD30.00
100mm
ADD TO CART 
T133-2, T134-2, T135-2 Scalpel handles
T133-2, T134-2, T135-2 Scalpel handles
SURGICAL KNIFE HANDLES

Bard Parker handles, all stainless steel, matt finish and grooved finger/ thumb grip. Length of handles only: No. 3 - 125mm; No. 4 -135mm; No. 5 - 160mm.

Scalpel blades and a list of matching handles and blades are on page L6.

T133-2
Scalpel handle No. 3, 125mm
10% DISCOUNT FOR 10
pk/2
ASK
T134-2
Scalpel handle No. 4, 135mm
10% DISCOUNT FOR 10
pk/2
ASK
T135-2
Scalpel handle No. 5, 160mm
10% DISCOUNT FOR 10
pk/2
ASK
TDS134-11 Swann-Morto scalpel with plastic handle
TDS134-11 Swann-Morto scalpel with plastic handle
TDS134-22 Swann-Morto scalpel with plastic handle
TDS134-22 Swann-Morto scalpel with plastic handle
DISPOSABLE SCALPELS, SWANN-MORTON

Swann-Morton disposable scalpels, sealed individually in trays, and boxed in units of 10. The sterile scalpels are individually packaged into a transparent thermo-formed tray, providing improved product visibility and assisting in safe passing techniques. When peeling the packet, the seal changes colour, thus indicating if the integrity of the packet has been breached and assuring the user of sterility up to the point of usage.
Stainless steel blade on polystyrene handle.

TDS134-11
Scalpels with plastic handle, SS, sterile, profile 11, Swann-Morton
10% DISCOUNT FOR 10
AUD35.00
box/10
ADD TO CART 
TDS134-22
Scalpels with plastic handle, SS, sterile, profile 22, Swann-Morton
10% DISCOUNT FOR 10
AUD35.00
box/10
ADD TO CART 
T161 A versatile dissecting kit consisting of 8 pieces in a durable pouch
T161 A versatile dissecting kit consisting of 8 pieces in a durable pouch
T162 Large dissecting kit
T162 Large dissecting kit
DISSECTING SETS

T161

A versatile dissecting kit consisting of 8 pieces in a durable tie pouch. Contains

  • 1pr straight dissecting scissors 115mm
  • 1pr curved dissecting scissors 125mm
  • 1 straight probe
  • 1 curved probe
  • 1pr splinter forceps 115mm
  • 1pr thumb forceps 115mm
  • 1 scalpel handle No. 4
  • 6 surgical blades

T162

Contents, see image including:

  • Probe
  • Sissors
  • Forceps
  • Ruler
  • Tweezers
  • Scalpel
T161
Dissecting set
10% DISCOUNT FOR 10
AUD28.00
set
ADD TO CART 
T162
Dissecting kit
10% DISCOUNT FOR 10
AUD39.00
kit
ADD TO CART 
Order Type / Payment Method / Address / Shopping Cart / Checkout